Adel M. Badawy Elshabasy
Adel M. Badawy Elshabasy
Emeritus Professor at Design and Production Engineering
Career Information
Academic Information
Awards
NA
Books
* Materials Eng., Part II, Testing, 2nd Ed. 2013, Books World Press, Cairo, Egypt.
* Materials Eng., Part II, Testing, 1st Ed. 1998, Books World Press, Cairo, Egypt.
* Engineering Materials and Testing, 2005-2010, Ministry of Higher Education, Cairo, Egypt.
* Modern Methods in Manufacturing, 1999: 2005, El-Hakim Press, Cairo, Egypt.
* Machining Materials and Processes, 1997, Ministry of Education, Books Sector, Cairo, Egypt.
Articles
NA
Publications
36- * Adel B. El-Shabasy et.al., “An investigation on mechanical and microstructural evolution of stationary shoulder friction stir welded aluminum alloy AA7075-T651”, J of Mech. Eng. Sci., Vol. 236 (12), pp. 6665–6676, 2022.
35- * Adel B. El-Shabasy et.al., “Surface Improvement of 7075 Alloy using Friction Stir Processing”, EGTRIB Journal, Vol 17 (2), pp. 1 - 12 ISSN 2090 - 5882, 2020
34- * Adel B. El-Shabasy et.al., “Assessment of steel wire’s fatigue life using finite elements modelling and experimental testing”, IOP Conf. Ser.: Mater. Sci. Eng. 973 012013, doi:10.1088/1757-899X/973/1/012013, 2020
33- * Adel B. El-Shabasy et.al., “Assessment of St. St. 316L joints welded by laser beam and metal active gas MAG processes”, IOP Conf. Ser.: Mater. Sci. Eng. 973 012027, doi:10.1088/1757-899X/973/1/012027, 2020
32- * Adel B. El-Shabasy et.al., “Modeling and Simulation of Small-Scale Biogas Digester Based on Kitchen Waste”, J. Env. Sci., ASU, Vol. 48 (2), Dec. 2019
31- * Adel B. El-Shabasy et.al., "Finite Element Modeling of Fatigue Life of Steel Wire", Engineering Research Journal 163, DES1 – DES11, September 2019
30- * Adel B. El-Shabasy et.al. "Assessment of AA7075/SiO2 Surface Composites Fabrication by Friction Stir Processing", IOP Conf. Series: Materials Science and Engineering 610, 012022, doi:10.1088/1757-899X/610/1/012022, 2019.
29- * Adel B. El-Shabasy et.al., "Alloy Segregation and Nano Structural Al-Composite Intrinsically Processing via DIMOX, Rheocasting, Thixocasting", Engineering. Research Journal (ERJ), 2019.
28- * Adel B. El-Shabasy et.al., "Evaluation of Stainless Steel.316L Joints Welded by Laser", JAUES, 2018
27- * Adel B. El-Shabasy et.al., "Effective Nanoparticles Feeding Treatment in Casting of A356/ZrO2 Nano-Reinforced Composite", The Minerals, Metals & Materials Society Serial 2018, Martin (ed.), Light Metals, pp. 1105-1111, 2018.
26- * Adel B. El-Shabasy et.al., "The Effect of Heat Treatment on Microstructure and Mechanical Properties of A356/ZrO2 Nano Reinforced composites", Proceedings of the 18th Int. AMME Conference, 3-5 April, 2018.
25- * Adel B. El-Shabasy et.al., "Comparison Between GMAW, GTAW and FSW Techniques Based on Power Consumption and Joint Strength"', Journal of American Science, 13(4), pp. 101-107, 2017.
24- * Adel B. El-Shabasy et.al., "Large Diameter Light-Scattering Complex Multipodal Nanotubes with Graded Refractive Index: Insights into Their Formation Mechanism and Photoelectochemical Performance", Journal of Materials Chemistry A, 2017.
23- * Adel B. El-Shabasy et.al., "Stationary Shoulder Friction Stir Welding Setup Design and Manufacturing", Proceedings of the Arab Conference for Creativity, Innovation and Competitiveness, Cairo, Egypt, May 24-25, 2016.
22- * Adel B. El-Shabasy et.al., "Fracture Assessment of Steel Sheet butt Joints Welded by GMAW and GTAW Techniques", 3rd International Conference in Africa & Asia on Welding & Failure Analysis of Engineering Materials, WAFA Egypt 2015, Luxor, Egypt, November 2-5, 2015.
21- * Adel B. El-Shabasy et.al., "Weldability Study of Low Carbon Low Alloy Steel Sheet Using Friction Stir Welding Process (FSW)", 3rd International Conference in Africa & Asia on Welding & Failure Analysis of Engineering Materials, WAFA Egypt 2015, Luxor, Egypt, November 2-5, 2015.
20- * Adel B. El-Shabasy et.al., “The effect of mixed mode I/II on the fracture toughness and fracture behavior of Nano-structured metal matrix composites”, Mater. Sci. Eng. A, 559, pp. 897-901, 2013.
19- * Adel B. El-Shabasy et.al., “Effects of Load Ratio, R, and Test Temperature on High Cycle Fatigue Behavior of Nano-Structured Al–4Y–4Ni-X Alloy Composites”, Mater. Sci. Eng. A, 558 (12), pp. 211-216, 2012.
18- * Adel B. El-Shabasy et.al., “The effects of changes in test temperature and loading conditions on fracture toughness of a toughened Zr-based bulk metallic glass composite”, Mater. Sci. Eng. A, 540, pp. 97-101, 2012.
17- * Adel B. El-Shabasy et.al., “Effects of Composition Changes on Strength, Bend Ductility, Toughness, and Flex bending Fatigue of Iron based Metallic Glass Ribbons”, Met. & Matr. Trans. A, 43 (8), pp. 2697-2705, 2012.
16- * Adel B. El-Shabasy et.al., “Fatigue Coaxing in Zr-based Bulk-Metallic Glass”, Scrip. Mater., 62, pp. 481-484, 2010.
15- * Adel B. El-Shabasy et.al, “High Cycle Fatigue Behavior of a Nanostructured Composite Produced via Extrusion of Amorphous Al89Gd7Ni3Fe1 Alloy Powder”, Mater. Sci. Eng. A 513-514, pp. 202-207, 2009.
14- * Adel B. El-Shabasy et.al., Putting the heat on nano-composite aluminium alloys, Metal Powder Report, Vol. 64, No. 5, pp. 28-34, 2009.
13- * Adel B. El-Shabasy et.al., “Effects of Microstructural Change, Loading Condition, and Test Temperature on Toughness of Fully Pearlitic Eutectoid Steel used in Transportation Industry”, Mater. Sci. Tech., 25 (3), pp. 369-378, 2009.
12- * Adel B. El-Shabasy et.al, “Utilization of the Agricultural Residues in Natural Fiber Polymer Composites (NFPCs)”, Third Ain Shams University International Conference on Environmental Engineering (ASCEE3), Vol. IV, pp. 25-40, Cairo, Egypt, April 2009.
11- * Adel B. El-Shabasy et.al., “Fracture and Fatigue Crack Growth of Nano-Composite Aluminum Alloys”, 1st International Joint Conference on Materials Science, Nanotechnology and Biotechnology, Jan. 4-6, 2009, Cairo, Egypt.
10- * Adel B. El-Shabasy et.al., “Fracture and Fatigue Crack Growth of Nano-Composite Aluminum Alloys”, 2008 World Congress on Powder Metallurgy and Particulate Materials, June 8-12, 2008, Washington, DC, USA.
9- * Adel B. El-Shabasy et.al., “Effects of Load-Ratio and Test Temperature on Fatigue Crack Growth of Fully Pearlitic Eutectoid Steel”, International Journal of Fatigue, 26 (3), pp. 305-309, 2004.
8- * Adel B. El-Shabasy, “Bond Shear Strength of Adhesive Bonded Laminates (ABL)”, Ain Shams Univ., Scientific Bulletin, Faculty of Eng., 39 (2), pp. 367-381, 2004, Hakim Press, English, Egypt.
7- * Adel B. El-Shabasy et.al., “Effect of Changes in Notch Radius and Mixed Mode Loading on Toughness of Fully Pearlitic Eutectoid Steel”, MS & T 2003, TMS Fall Meeting, and 45th ISS Conference, Chicago, Illinois USA, November 9-12, 2003, English, USA.
6- * Adel B. El-Shabasy et.al., “Effects of Load-Ratio, R, and Test Temperature on Fatigue Crack Growth Behavior of Fully Pearlitic Eutectoid Steel”, MS & T 2003, TMS Fall Meeting, and 45th ISS Conference, Chicago, Illinois USA, November 9-12, 2003, English, USA.
5- * Adel B. El-Shabasy and E. Ismail, “Effect of Microwave Oven Drying on Some Properties of Phosphate-Bonded Investment Materials, Egyptian Dental Journal, 47(1), pp. 475-483, 2001, Dar El-Hekma Press, English, Egypt.
4- * Adel B. El-Shabasy et. Al., “Evaluation of Some Mechanical Properties of Ethylene Vinyl Acetate Mouth Guard Materials”, Egyptian Dental Journal, 46 (10), pp.1839-1846, 2000, Dar El-Hekma Press, English, Egypt.
3- * Adel B. El-Shabasy et.al, “Status and Environmental Upgrading of Small Foundries in Greater Cairo”, Cairo 7th International Conference on Energy and Environment, Cairo, Egypt, 2000,English, Egypt.
2- * Adel B. El-Shabasy et.al, “Safety, Health and Environmental Impact from Egyptian Small Foundries”, 14th Annual International Occupational Ergonomics and Safety Conference, Florida, Orlando, USA, 1999, English, USA.
1- * Adel B. El-Shabasy et.al. “Study of the Variation of Tensile Strength across the Cross section of Date Palm Leaves Midrib”, The 5th European Conference on Advanced Materials and Processes (EROMAT 97), Maastricht, Netherlands, 21-23 April 1997.
Research Projects
* Processing and Mechanical Properties of Amorphous Metal Foil and Laminates
U.S.-Egypt Science & Technology Joint Fund (MAN 11-006-004).
* Foundries and Lead Smelters in Cairo: Air Pollution Problem and Possible Remediation.
* An Integrated Approach to the Environmental Upgrading of Egyptian Small Foundries,
(with Emphasis on Lead Smelters).